Powder Skiing - Common Powder Problems and How to Solve Them

Most skiers are having problems when Skiing in Powder, and that it entails more effort and hard work to fully enjoy Powder Skiing compared to groomed slopes. It is indeed true that skiers can commit a lot of errors and face many problems in Powder but there is a solution when you find yourself on a tight spot. In this section, be acquainted with some of the common problems that skiers experience in Powder and learn how to solve them:

Problem: Skis dive in Powder
It is possible that it has something to do with your Ski Boot and Ski Binding combination. It can also be that your Skis do not have wax or the wax is applied improperly. Likewise, too much forward lean in the lower leg will make your Skis to go deep.
Solution/s: Check your equipment. Make sure that your Ski Boots are not too stiff-flexing. Your Skis will float if you have softer-flexing Ski Boots because you will be able to keep balance and there will be more room for your ankles. Make the upper buckles a little loose and test if it works. If your Skis float in Powder, then you need a pair of less stiff Ski Boots.

Another solution in preventing your Skis from diving into Powder is to check your Ski Binding placement. It would be better if your Ski Bindings have fore-aft adjustment range. With this feature, you will be able to adjust the setting, depending on the need. If you want to Carve, you can set them forward, or if you are into Powder Skiing, set them at the middle.

As for your Skis, proper waxing is important. Remember that you will never have a good time in Powder if you cannot reach a floating speed just because your Skis lack wax. Make sure that your Skis have proper and sufficient applications of wax.

Problem:Unable to handle both Skis
Not being able to manage both your Skis can be due to your left and right sides which are aligned differently. It can also be the Snow crammed between your Ski Boots and Ski Bindings. Another reason is not enough flex of your lower body.
Solution/s: If you have a sound alignment, your Skis will ride flat when they are supposed to. Make sure to check your alignment. You can undergo methods like the plumb bob-type test and the Devil Level test. The plumb bob-type testing is a static assessment that can tell the good alignment of your knees, while the Devil Level test provides details on how your Skis are riding. With your Skis on, stand on a foam sleeping pad on a completely flat floor. One Devil Level (carpenter's circular protractor) is placed on the flat part of topsheet of each Ski. These levels will give you an idea on the objective measurement of each Ski. Ask the help of someone to read on how your Skis are riding in terms of degrees and half-degrees.

Make sure to clean off the bottom part of your Ski Boots after a crash in Powder. Your Skiing will be affected if you have Snow packed on your equipment.

As for the insufficient flex of your lower body, apply enough pressure on your inside Ski in order to prevent it from moving away from your outside Ski and rising into the surface.

Problem: Difficulty in carving a turn
when carving a turn in Powder, you need to bend both Skis. But this is a hard thing to do for some skiers. It can be related to lack of proper timing and/or very stiff Skis.
Solution/s: You need proper timing especially in pressuring motions which you use in bending your Skis into arcs. It is important to be on the middle ground - do not bend your Skis too little or too much.

Skis which are too long for you will find it difficult to bend easily. The same goes for Skis which are too stiff. Make sure that you have Skis with the Ski Length appropriate for you and with the right Ski Stiffness suitable for Powder.

You will encounter a lot of problems as you embark on Powder Skiing. It is better if you have some ideas on what most skiers face in Powder Skiing. This will give you guidelines on what to do should these problems occur, or better yet, learn from these common problems and avoid doing the same mistakes as you hit Powder.